Installation Guide
A Professional Guide to Wallpaper Installation
How to measure, prepare, paste, and hang wallpaper for a seamless finish that lasts — the techniques professional decorators use on every project.
Wallpaper adds texture, colour, and pattern to a room in a way that paint alone cannot, but it also demands more skill to get right. A poorly hung wallpaper job is immediately visible — mismatched patterns, gapping seams, trapped air bubbles, and edges that lift within weeks. The difference between a professional finish and a DIY attempt almost always comes down to preparation and technique, not the paper itself. This guide walks through the four stages of wallpaper installation — measuring and planning, preparing the wall, cutting and pasting, and hanging and smoothing — using the same methods professional decorators rely on. Whether you are papering a feature wall or an entire room, following these steps will help you achieve a flat, seamless finish with seams that stay tight and patterns that line up across the full width of the wall.
Measure and Plan
Start by measuring the full height and width of each wall, accounting for doors, windows, and alcoves. Add 10 to 15 centimetres to each drop length to allow for trimming and pattern matching. Calculate the number of rolls you need by dividing the total wall width by the roll width, then multiplying by the number of drops. Always buy one extra roll — dye lots vary between batches, and running out mid-project means a colour mismatch on the replacement roll. Note the pattern repeat measurement on the roll label; large repeats waste more paper and increase the number of rolls required. Sketch a rough plan showing where each seam will fall, keeping seams away from the direct sightline of the main entrance where possible.
Prepare the Wall Surface
Wallpaper will not adhere properly to a dirty, flaking, or porous surface. Strip any existing wallpaper completely — never paper over old paper, as the moisture from the paste softens the old adhesive and causes bubbles and lifting. Wash the wall with a sugar soap solution to remove grease and grime, then rinse with clean water and allow it to dry fully. Fill any cracks, holes, or dents with filler, sand smooth, and prime bare plaster with a diluted paste size or specialist primer. This sealing layer prevents the plaster from absorbing paste too quickly, which causes the paper to dry out and peel. For newly plastered walls, wait at least four weeks before papering to allow the plaster to cure.
Cut and Paste the Paper
Cut each drop to length on a clean, flat surface, marking the top of each piece so the pattern runs the same direction. If using a patterned paper, match the repeat before cutting the second drop. Apply paste evenly with a pasting brush or roller, working from the centre of the strip outward to the edges — dry edges are the most common cause of lifting seams. Book the paper by loosely folding it paste-to-paste and letting it rest for the time specified on the paste instructions, usually five to ten minutes. This allows the paper to expand before it goes on the wall, preventing stretched seams and bubbles after drying. For paste-the-wall papers, apply paste directly to the wall instead.
Hang and Smooth
Start at a corner or a plumb line drawn on the wall, not at the corner itself which is rarely true. Position the top of the drop at the ceiling line, leaving the excess overlap, and smooth it down with a wallpaper brush or plastic smoother, working from the centre outward to push out air bubbles. Use a seam roller gently on the edges once the paper is in position — pressing too hard squeezes out paste and weakens the join. Trim the top and bottom excess with a sharp knife and a straight edge. Butt the next drop against the first with no overlap, matching the pattern exactly. Wipe each seam immediately with a damp sponge to remove excess paste before it dries, as dried paste leaves a visible sheen on the surface.
Professional Tips for a Flawless Finish
Keep the room well-ventilated but avoid draughts, which cause paper to dry too quickly and shrink at the seams.
Use a spirit level to draw a plumb line for the first drop — corners are rarely straight.
Number each cut drop on the back in pencil so you hang them in the correct order.
Switch off radiators near the wall being papered; heat accelerates drying and causes seam gaps.
Keep a clean bucket of water and sponge nearby to wipe paste off the surface immediately.
Want a professional wallpaper finish?
EHT Decorators handles wallpaper installation to a flawless standard. Get a detailed quote today.
Request a Quote